Fairbanks LoadTronic 3 - Loader Weighing System User Manual

51248 Revision 1 07/10

page 10 The LOADTRONIC 3 starts up in automatic weighing mode. Press the downarrow to open the main menu; press the down- or up arrow to highlight the

OPERATOR’S MANUAL page 11CHAPTER 3 Operating LOADTRONIC 3 3.1 Start –Normal Operation LOADTRONIC 3 starts up as the machine’s ignition key is set

page 12 The weight of the bucket is automatically added to the running total weight. During automatic weighing the display unit shows, refer Figure 3

OPERATOR’S MANUAL page 13Note: If the bucket is not fully tilted rearward, the message:‘BUCKET’ will be shown in place of the bucket weight (no w

page 14 3.2.1 Tips for best results when weighingMaximum function and accuracy is achieved by avoiding substantial deviations from the usual work cycl

OPERATOR’S MANUAL page 15renewed weighing by moving the gear selector from forward or neutral to reverse.3.3 Recording LOADTRONIC 3 records each

page 16 3.3.2 Unspecified Recording LOADTRONIC 3 allows the operator to perform an unspecified recording; a recording of material weight without any s

OPERATOR’S MANUAL page 17Procedure to start an unspecified job record with a specified target load:1. Press 0 on the keypad to open job record no

page 18 Procedure to specify job details for a job record: 1. Press a job record number directly using the keypad; job record 0 will not store the det

OPERATOR’S MANUAL page 193.3.4 Selecting a Pre-defined Job Record If the operator has a set of pre-defined jobs to perform, the assigned job reco

page 2 AADI Document W150 H70 001 1st Edition 14th September 2007 Preliminary Edition 2nd Edition 11th January 2008 © Copyright: Aanderaa

page 20 Job record 1-9 can be active jobs. A job becomes active once the first bucket of material is delivered; the operator can easily see that a job

OPERATOR’S MANUAL page 213.5 Changing and Deleting Attachment 10 different attachments can be used with LOADTRONIC 3. The current attachments ID

page 22 Note! The system will block the automatic weighing function and indicate the requirement with the message ‘Adjust Zeropoint’ until the zeropoi

OPERATOR’S MANUAL page 235. Operate the lifting arm at a slow and even speed according to the instructions on the display: Lower – Lift – Lower,

page 24 6. When the zeropoint adjusting is OK and completed, the LOADTRONIC 3 automatically returns to automatic weighing after showing the adjustment

OPERATOR’S MANUAL page 25Probable cause: x Uneven movements of the lifting arm mechanism during taring. x The adjustment was more than r 4% of ma

page 26 Procedure to adjust the material in the bucket: 1. Press and hold * for at least 1 second to cancel the bucket weight from the running total

OPERATOR’S MANUAL page 275. Raise the bucket evenly from below the horizontal level. The remaining load in the bucket is weighed, and the weight

page 28 3.11 Adjusting the Display Backlight When LOADTRONIC 3 is in pause mode, the intensity of the background light of the display can be adjusted

OPERATOR’S MANUAL page 29Figure 3-13 Example of an error message.

OPERATOR’S MANUAL page 3Table of Contents CHAPTER 1 Description of LOADTRONIC 3 ... 5

page 30 CHAPTER 4 Library and Reports This chapter describes how to add customers, materials, trucks and location in a library for repeated use (refer

OPERATOR’S MANUAL page 314. If the library contains a description starting with this character, the description is shown in the Description-field

page 32 Customer Description: Press job record/F3 and open the correct record number. Press Next/F4 until the Customer ID/description is highlighted.

OPERATOR’S MANUAL page 33in the text field else the text reads ‘unspecified’. Press l/F3 to toggle between the index field and the text field. Pr

page 34 - Press F4 to clear all letters.Press Save/# to store the location with the location number in the library.4.1.4 Enter Job Details from the Te

OPERATOR’S MANUAL page 35Edit the Customer: 1. Open Main Menu - Text Editing – Customers, refer chapter 2.1. 2. Type the Customer ID number direc

page 36 Edit the Truck: 1. Open Main Menu - Text Editing – Truck, refer chapter 2.1. 2. Type the Truck ID number directly using the keypad, or set the

OPERATOR’S MANUAL page 37Edit Location: 1. Open Main Menu - Text Editing – Location, refer chapter 2.1. 2. Type the Location ID number directly u

page 38 - Press F2 to toggle between capital and small letters. - Press F3 to clear the last letter. - Press F4 to clear all letters. 5. Set the mater

OPERATOR’S MANUAL page 39- Press F3 to clear the last letter. - Press F4 to clear all letters. 5. Press Save/# to store the description with the

page 4 4.2 Reports ...394.2.1 Report H

page 40 4.2.2 Total Load ReportThe default setting is to make a report of the total weight loaded during a certain time period without specifying Cust

OPERATOR’S MANUAL page 41date. Press and hold the arrow to step one month at a time. Press Next/F4 to highlight the ‘To’ date, and the arrows to

page 42 Procedure to build a specified report: 1. Open Main Menu - Reports, refer chapter 2.1.2. Set the time period: The default date is the current

OPERATOR’S MANUAL page 43Perform similar for the Material-, Truck- and Location-field to set all your criteria. 5. Press Print/F2 to print the r

page 44 Procedure to make a copy of a receipt: 1. Open Main Menu - Reports, refer chapter 2.1.2. Specify the report, refer chapter 4.2.3. Press Select

OPERATOR’S MANUAL page 45CHAPTER 5 Maintenance Open Main Menu – Service, refer chapter 2.1.Service Functions holds submenus for sensor test, log

page 46 System Information holds information about e.g. software versions and legal system files.5.1 Load List, Event List and Error List There are 4

OPERATOR’S MANUAL page 47The Error list states system error, e.g. missing sensor, zeropoint failure etc. 5.2 Backup and Restore Logfiles, Databa

page 48 device with ID number 001 will only restore files from the \Loadtronic \ID_001 directory.Perform a backup: 1. Open Main Menu – Service – USB M

OPERATOR’S MANUAL page 495.3 Copy Calibration Details The attachment descriptions are stored in ID number 1 to 10; calibration details are stored

OPERATOR’S MANUAL page 5CHAPTER 1 Description of LOADTRONIC 3 LOADTRONIC 3 is an automatic and dynamic weighing system for wheel loaders. It is a

page 50 5.4 System Information System information holds two pages displaying information about software version, main unit serial number, OIML require

OPERATOR’S MANUAL page 51Figure 5-8 System Information, page 2.

page 6 x To carry out calibration and similar functions when the calibration switch is set to the enabled position. x To present measurement results o

OPERATOR’S MANUAL page 71.5 Remote Wireless Communication (Optional) Wireless communication is used for up- and downloading data between the whee

page 8 CHAPTER 2 Operator Display and Menu LOADTRONIC 3 has a set of function keys, F1, F2, F3, F4, #,n,p, and *on the display unit, refer Figure 2-1

OPERATOR’S MANUAL page 92.1 Menu Layout Figure 2-2 Illustration of the LOADTRONIC 3 menu.